If you are having problems getting imap_mail_copy and imap_mail_move to work, check you have installed imap_devel (the imap development libraries) as well as imap (the imap daemon). Without it, PHP appears to configure correctly --with-imap, but some functions do not work.
It took me about 12 hours to figure this out!!
imap_mail_copy
(PHP 4, PHP 5, PHP 7, PHP 8)
imap_mail_copy — Copy specified messages to a mailbox
Descripción
Copies mail messages specified by message_nums
to specified mailbox.
Parámetros
-
imap -
An IMAP\Connection instance.
-
message_nums -
message_numsis a range not just message numbers (as described in » RFC2060). -
mailbox -
The mailbox name, see imap_open() for more information
AdvertenciaEl paso de datos no confiables a este parámetro es inseguro, a menos que imap.enable_insecure_rsh esté inhabilitado.
-
flags -
flagsis a bitmask of one or more of-
CP_UID- the sequence numbers contain UIDS -
CP_MOVE- Delete the messages from the current mailbox after copying. If this flag is set, the function behaves identically to imap_mail_move().
-
Valores devueltos
Devuelve true en caso de éxito o false en caso de error.
Historial de cambios
| Versión | Descripción |
|---|---|
| 8.1.0 |
The imap parameter expects an IMAP\Connection
instance now; previously, a valid imap recurso was expected.
|
add a note
User Contributed Notes 5 notes
marcus at names dot co dot uk ¶
22 years ago
jigar dot dhaduk79 at gmail dot com ¶
9 years ago
When we want to copy more than one mail, we can write '(string)' before msg_num. Like..
$msg_num = "1,2,3,4,5,6,7";
$copy = imap_mail_copy($imap_stream, (string) $msg_num, '[Gmail]/Important', CP_UID);
Ben ¶
11 years ago
If you use this function and you get the following notice:
Notice: Unknown: IMAP protocol error: Could not parse command (errflg=2) in Unknown on line 0
Notice: Unknown: Could not parse command (errflg=2) in Unknown on line 0
you should check the function parameters. This notice appears (according to what I found on the internet and my problems) when it gets an invalid $msglist. So be sure to give the right number (as a String!):
"$msg_num", $msg_num or (string) $msg_num.
Dont use '$msg_num' when calling the function, this will literally send the string $msg_num.
You can give a string like "1,3,5,7,8", which will work perfectly fine to move the given mails.
I had all my mailnumbers in an array ( $messageSet) and used
<?php
$messageSetImpl = implode ( "," , $messageSet );
imap_mail_copy( $imapStream, $messageSetImpl, $mailBox )
?>
What I hadn't had thougt of was that my $messageSet was sometimes empty, that was when I got the notice. So you might want to check that by putting first:
<?php
if ( !( empty( $messageSet ) ) ) {
$messageSetImpl = implode ( "," , $messageSet );
imap_mail_copy( $imapStream, $messageSetImpl, $mailBox )
}
?>
That should work.
hxlvt at hotmail dot com ¶
23 years ago
After much fooling around, imap_mail_copy did work for me. One thing you might want to check, if you are having problems, is the new mailbox name. Make sure it is just a folder name, e.g. INBOX.haha without the server part.
richard dot oplustil at gmail dot com ¶
12 years ago
imap_ mail_ move and imap_mail_copy don't work with sequence numbers on MS Exchange. imap_ uid in combination with CP_UID works fine.
