If you setting hex values correct format is:
snmpset($source_ip,$community,"$oid","x","10 10 10 10");
(PHP 4, PHP 5, PHP 7)
snmpset — Set the value of an SNMP object
$host
, string $community
, string $object_id
, string $type
, mixed $value
[, int $timeout
= 1000000
[, int $retries
= 5
]] )
snmpset() is used to set the value of an SNMP object
specified by the object_id
.
host
The hostname of the SNMP agent (server).
community
The write community.
object_id
The SNMP object id.
type
The MIB defines the type of each object id. It has to be specified as a single character from the below list.
= | The type is taken from the MIB |
i | INTEGER |
u | INTEGER |
s | STRING |
x | HEX STRING |
d | DECIMAL STRING |
n | NULLOBJ |
o | OBJID |
t | TIMETICKS |
a | IPADDRESS |
b | BITS |
If OPAQUE_SPECIAL_TYPES
was defined while compiling the SNMP library, the following are also valid:
U | unsigned int64 |
I | signed int64 |
F | float |
D | double |
Most of these will use the obvious corresponding ASN.1 type. 's', 'x', 'd' and 'b' are all different ways of specifying an OCTET STRING value, and the 'u' unsigned type is also used for handling Gauge32 values.
If the MIB-Files are loaded by into the MIB Tree with "snmp_read_mib" or by specifying it in the libsnmp config, '=' may be used as
the type
parameter for all object ids as the type can then be automatically read from the MIB.
Note that there are two ways to set a variable of the type BITS like e.g. "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":
See examples section for more details.
value
The new value.
timeout
The number of microseconds until the first timeout.
retries
The number of times to retry if timeouts occur.
성공 시 TRUE
를, 실패 시 FALSE
를 반환합니다.
If the SNMP host rejects the data type, an E_WARNING message like "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length." is shown. If an unknown or invalid OID is specified the warning probably reads "Could not add variable".
Example #1 Using snmpset()
<?php
snmpset("localhost", "public", "IF-MIB::ifAlias.3", "s", "foo");
?>
Example #2 Using snmpset() for setting BITS SNMP object id
<?php
snmpset("localhost", "public", 'FOO-MIB::bar.42', 'b', '0 1 2 3 4');
// or
snmpset("localhost", "public", 'FOO-MIB::bar.42', 'x', 'F0');
?>
If you setting hex values correct format is:
snmpset($source_ip,$community,"$oid","x","10 10 10 10");
The "type" parameter must be one of the following, depending on the type of variable to set on the SNMP host:
i INTEGER
u unsigned INTEGER
t TIMETICKS
a IPADDRESS
o OBJID
s STRING
x HEX STRING
d DECIMAL STRING
n NULLOBJ
b BITS
If OPAQUE_SPECIAL_TYPES was defined while compiling the SNMP library, the
following are also valid:
U unsigned int64
I signed int64
F float
D double
As an example, using "i" would set an integer, and "s" would set a string. If the SNMP host rejects the data type, you might get the following message: "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length."
If you specify an unknown or invalid OID, you might get a "Could not add variable" message. When specifying an absolute OID (one that is already resolved) that is completely numeric, prepend it with a period. For example, an OID that could enable/disable Ethernet ports on an Asante hub might be "1.3.6.1.2.1.22.1.3.1.1.3.6.4.0", but you would need to use ".1.3.6.1.2.1.22.1.3.1.1.3.6.4.0" in the OID parameter so that the SNMP library won't try to resolve an already resolved OID. Friendly, unresolved OIDs do not need the period prepended, such as "system.SysContact.0"
Note that there are two ways to set a variable of the type BITS like e.g.:
SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}
1. Using type "b" and a list of bit numbers like:
snmpset('FOO-MIB::bar.42', 'b', '0 1 2 3 4');
with the disadvantage that the success is not easily verifyable as an snmpget() for the same OID would return e.g. 0xF8.
2. Using type "x" and a hex number but without(!) the usual "0x" prefix:
snmpset('FOO-MIB::bar.42', 'x', 'F0');
If you have importet the MIB-Files into the MIB Tree with "snmp_read_mib" you may use '=' as the "type" parameter.
In this case the type will also be taken from the loaded mib file. (Octest strings will be interpreted like strings though)
Comes in handy for a more dynamic use of snmpset.