It appears that mcrypt_decrypt pads the *RETURN STRING* with nulls ('\0') to fill out to n * blocksize. For old C-programmers, like myself, it is easy to believe the string ends at the first null. In PHP it does not:
strlen("abc\0\0") returns 5 and *NOT* 3
strcmp("abc", "abc\0\0") returns -2 and *NOT* 0
I learned this lesson painfully when I passed a string returned from mycrypt_decrypt into a NuSoap message, which happily passed the nulls along to the receiver, who couldn't figure out what I was talking about.
My solution was:
<?php
$retval = mcrypt_decrypt( ...etc ...);
$retval = rtrim($retval, "\0"); // trim ONLY the nulls at the END
?>
mcrypt_decrypt
(PHP 4 >= 4.0.2, PHP 5, PHP 7 < 7.2.0, PECL mcrypt >= 1.0.0)
mcrypt_decrypt — Déchiffre un texte avec les paramètres donnés
Avertissement
Cette fonction est OBSOLÈTE à partir de PHP 7.1.0 et a été SUPPRIMÉE à partir de PHP 7.2.0. Dépendre de cette fonction est fortement déconseillé.
Description
mcrypt_decrypt(
string
string
string
string
string
): string|false
string
$cipher,string
$key,string
$data,string
$mode,string
$iv = ?): string|false
Déchiffre les données data et retourne les données déchiffrées.
Liste de paramètres
-
cipher -
Une constante parmi les constantes
MCRYPT_ciphername, ou le nom de l'algorithme, sous la forme d'une chaîne de caractères. -
key -
La clé utilisée lors du chiffrement des données. Si la taille de la clé fournit n'est pas supportée par le cipher, la fonction émettra un warning et retournera
false -
data -
Les données qui seront déchiffrées avec utilisant les paramètres
cipheretmode. Si la taille des données ne correspond pas à n * la taille du bloc, les données seront complétées par des '\0'. -
mode -
Une constantes parmi les constantes
MCRYPT_MODE_modename, ou une des chaînes suivantes : "ecb", "cbc", "cfb", "ofb", "nofb" ou "stream". -
iv -
Utilisé pour l'initialisation des modes CBC, CFB, OFB, ainsi que dans quelques algorithmes du mode STREAM. Si la taille de l'IV fourni n'est pas supporté par le mode d'opération ou si vous ne fournissez pas d'IV, mais que le mode d'opération en requiert un, la fonction émettra un avertissement et retournera
false.
Valeurs de retour
Retourne les données déchiffrées sous la forme d'une chaîne de caractères
ou false si une erreur survient.
add a note
User Contributed Notes 8 notes
eddiec at stararcher dot com ¶
19 years ago
gmmarco at outlook dot my ¶
6 years ago
Look at http://php.net/manual/en/function.openssl-decrypt.php for a replacement.
Supports PHP 5 >= 5.3.0, PHP 7
pnz dot r00t at yandex dot ru ¶
8 years ago
When i using this function i find some problem, with adding additional binary symbols in decode message.
$sDecrypt – «2433091»
$sDecrypt strlen – 16 (before trim)
$sDecrypt – «2433091»
$sDecrypt strlen – 7 (after trim)
At local PC this problem solved by using trim/trim, but if I send my encrypt message to sever, and try encrypt them, I see that my message is not 16 symbols, as it was in my local pc, it is 32 sybmols, after encode. And trim function not working. I look at symbols code and what I see
50
52
51
51
48
57
49
0
0
0
0
0
0
0
0
0
10
158
112
183
154
27
95
85
42
35
95
54
227
41
179
77
After “tabulation symbols” I get some junk symbols, and I solve this problems like this.
After mcrypt_decrypt I use this code
$plaintext_dec = substr($plaintext_dec, 0, strpos($plaintext_dec, "\0"));
I think it is not best resolution for this problem, but I solve my problem :)
david at sickmiller dot com ¶
16 years ago
If you happen to be decrypting something encrypted in ColdFusion, you'll discover that its encrypt function apparently pads the plaintext with ASCII 4, the "end of transmission" character.
Building on eddiec's code, you can remove both nulls and EOTs with this:
<?php
$retval = mcrypt_decrypt( ...etc ...);
$retval = rtrim($retval, "\0\4"); // trim ONLY the nulls and EOTs at the END
?>
beltrachi ¶
13 years ago
Caution, MCRYPT_RIJNDAEL_256 is not equivalent to AES_256.
The way to make RIJNDAEL be decrypted from AES with openssl is to use MCRYPT_RIJNDAEL_128 and padd the string to encrypt before encrypting with the follwing function:
<?php
function pkcs5_pad ($text, $blocksize) {
$pad = $blocksize - (strlen($text) % $blocksize);
return $text . str_repeat(chr($pad), $pad);
}
?>
On the decryption, the choosing of AES_256 or AES_128, etc. is based on the keysize used in the crypting. In my case it was a 128bit key so I used AES_128.
evangelion207 at hotmail dot com ¶
13 years ago
Be careful, sometimes mcrypt_decrypt return additional white spaces to the uncrypted string; use trim() for deleting them. I was like 2 hours searching the error and it was that..
Anonymous ¶
13 years ago
To remove PKCS7 padding:
<?php
$decrypted = mdecrypt_generic($td, base64_decode($enc_auth_token));
$dec_s = strlen($decrypted);
$padding = ord($decrypted[$dec_s-1]);
$decrypted = substr($decrypted, 0, -$padding);
?>
artaxerxes2 at iname dot com ¶
11 years ago
To decrypt data coming from MySQL's AES_ENCRYPT function:
<?php
function mysql_aes_key($key)
{
$new_key = str_repeat(chr(0), 16);
for($i=0,$len=strlen($key);$i<$len;$i++)
{
$new_key[$i%16] = $new_key[$i%16] ^ $key[$i];
}
return $new_key;
}
function aes_decrypt($encrypted,$key)
{
// if $encrypted is HEXed, then return it to binary
$encrypted = pack('H*',$encrypted);
$key = mysql_aes_key($key);
return rtrim(mcrypt_decrypt(MCRYPT_RIJNDAEL_128,$key,$encrypted,MCRYPT_MODE_ECB,''),"\x00..\x1F");
}
?>
adapted from the article "Replicating MySQL AES Encryption Methods With PHP" (dated 2012-05-20) found somewhere online.
