The remark "in PHP the switch statement is considered a looping structure for the purposes of continue" near the top of this page threw me off, so I experimented a little using the following code to figure out what the exact semantics of continue inside a switch is:
<?php
for( $i = 0; $i < 3; ++ $i )
{
echo ' [', $i, '] ';
switch( $i )
{
case 0: echo 'zero'; break;
case 1: echo 'one' ; XXXX;
case 2: echo 'two' ; break;
}
echo ' <' , $i, '> ';
}
?>
For XXXX I filled in
- continue 1
- continue 2
- break 1
- break 2
and observed the different results. This made me come up with the following one-liner that describes the difference between break and continue:
continue resumes execution just before the closing curly bracket ( } ), and break resumes execution just after the closing curly bracket.
Corollary: since a switch is not (really) a looping structure, resuming execution just before a switch's closing curly bracket has the same effect as using a break statement. In the case of (for, while, do-while) loops, resuming execution just prior their closing curly brackets means that a new iteration is started --which is of course very unlike the behavior of a break statement.
In the one-liner above I ignored the existence of parameters to break/continue, but the one-liner is also valid when parameters are supplied.
continue
continue는 루프 구조 내부에서 현재 루프 반복의 나머지 부분을 생략하고 조건 평가를 한 후 다음 반복 시작에서 실행을 지속하게 합니다.
Note: PHP에서 switch구문은 continue에 의해 루프 구조로 사용할수 있다는것을 참고할것.
continue는 숫자 인수 옵션을 사용하여 루프의 깊이를 표시할수 있고, 루프의 끝까지 건너뛸수 있다.
<?php
while (list($key, $value) = each($arr)) {
if (!($key % 2)) { // skip odd members
continue;
}
do_something_odd($value);
}
$i = 0;
while ($i++ < 5) {
echo "Outer<br />\n";
while (1) {
echo " Middle<br />\n";
while (1) {
echo " Inner<br/ >\n";
continue 3;
}
echo "This never gets output.<br />\n";
}
echo "Neither does this.<br />\n";
}
?>
continue 뒤의 세미콜론을 빼먹으면 혼란스러울 것입니다. 여기에 해서는 안되는 일의 예제입니다:
<?php
for ($i = 0; $i < 5; ++$i) {
if ($i == 2)
continue
print "$i\n";
}
?>
기대했던 결과는:
0 1 3 4
하지만 스크립트의 출력은:
2
print 호출의 반환값은 int(1)이기 때문에, 위에서 언급한 선택적인 수 인수로 간주합니다.
add a note
User Contributed Notes 7 notes
jaimthorn at yahoo dot com ¶
14 years ago
Nikolay Ermolenko ¶
15 years ago
Using continue and break:
<?php
$stack = array('first', 'second', 'third', 'fourth', 'fifth');
foreach($stack AS $v){
if($v == 'second')continue;
if($v == 'fourth')break;
echo $v.'<br>';
}
/*
first
third
*/
$stack2 = array('one'=>'first', 'two'=>'second', 'three'=>'third', 'four'=>'fourth', 'five'=>'fifth');
foreach($stack2 AS $k=>$v){
if($v == 'second')continue;
if($k == 'three')continue;
if($v == 'fifth')break;
echo $k.' ::: '.$v.'<br>';
}
/*
one ::: first
four ::: fourth
*/
?>
Koen ¶
12 years ago
If you use a incrementing value in your loop, be sure to increment it before calling continue; or you might get an infinite loop.
rjsteinert.com ¶
13 years ago
The most basic example that print "13", skipping over 2.
<?php
$arr = array(1, 2, 3);
foreach($arr as $number) {
if($number == 2) {
continue;
}
print $number;
}
?>
www.derosetechnologies.com ¶
20 years ago
In the same way that one can append a number to the end of a break statement to indicate the "loop" level upon which one wishes to 'break' , one can append a number to the end of a 'continue' statement to acheive the same goal. Here's a quick example:
<?
for ($i = 0;$i<3;$i++) {
echo "Start Of I loop\n";
for ($j=0;;$j++) {
if ($j >= 2) continue 2; // This "continue" applies to the "$i" loop
echo "I : $i J : $j"."\n";
}
echo "End\n";
}
?>
The output here is:
Start Of I loop
I : 0 J : 0
I : 0 J : 1
Start Of I loop
I : 1 J : 0
I : 1 J : 1
Start Of I loop
I : 2 J : 0
I : 2 J : 1
For more information, see the php manual's entry for the 'break' statement.
tufan dot oezduman at gmail dot com ¶
18 years ago
a possible explanation for the behavior of continue in included scripts mentioned by greg and dedlfix above may be the following line of the "return" documentation: "If the current script file was include()ed or require()ed, then control is passed back to the calling file."
The example of greg produces an error since page2.php does not contain any loop-operations.
So the only way to give the control back to the loop-operation in page1.php would be a return.
Geekman ¶
16 years ago
For clarification, here are some examples of continue used in a while/do-while loop, showing that it has no effect on the conditional evaluation element.
<?php
// Outputs "1 ".
$i = 0;
while ($i == 0) {
$i++;
echo "$i ";
if ($i == 1) continue;
}
// Outputs "1 2 ".
$i = 0;
do {
$i++;
echo "$i ";
if ($i == 2) continue;
} while ($i == 1);
?>
Both code snippets would behave exactly the same without continue.
